COOLING MODE
The cooling function allows the air
conditioner to cool the room and
reduce Air humidity at the same
time.
To activate the cooling function (COOL), press the
MODE button until the symbol appears on
the display.
With the button or set a temperature lower
than that of the room.
HEATING MODE
HEAT The heating function allows the air
conditioner to heat the room.
To activate the heating function (HEAT), press the
MODE button until the symbol appears on the
display.
With the button or set a temperature higher
than that of the room.
In HEATING operation, the appliance can
automatically activate a defrost cycle, which
is essential to clean the frost on the condenser
so as to recover its heat exchange function.
This procedure usually lasts for 2-10 minutes.
During defrosting, indoor unit fan will stop
operation. After defrosting, it resumes to
HEATING mode automatically.
(For North American market)
If necessary, you can press ECO button 10
times within 8 seconds under heating mode
to start the forced defrosting. It will defrost
the outdoor ice much faster.
FAN MODE (Not FAN button)
Fan mode, air ventilation only.
To set the FAN mode, press MODE until
appears on the display
DRY MODE
This function reduces the humidity
of the air to make the room more
comfortable.
To set the DRY mode, Press MODE until
appears in the display. An automatic function of
pre-setting is activated
FAN SPEED function (FAN button)
F Change the operating fan speed.
Press FAN button to set the running fan speed,
it can be set to AUTO/ MUTE/ LOW/ LOW-MID
/ MID/ MID-HIGH/ HIGH/ TURBO speed circularly.
AUTO MODE
AUTO Automatic mode.
To set the AUTO mode, press MODE until
appears on the display.
In AUTO mode the run mode will be set
automatically according to the room temperature
Child-Lock function
1. Hold MODE and TIMER button together
to active this function, and do it again to
deactivate this function.
2. Under this function, no single button will be
Active
SWING BUTTON
1. Press the button SWING to activate the louver,
1.1 Press to activate the horizontal flaps
to swing from up to down, the will appear
on the remote display.
Press again to stop the swing movement at
the current angle.
1.2 Press to active the vertical deflectors
to swing from left to right, the will appear
on the remote display.
Press again to stop the swing movement at
the current angle.
2.If the vertical deflectors are positioned manually
which placed under the flaps, they allow to move
the air flow direct to rightward or leftward.
3.For some inverter heating models, press
horizontal SWING and vertical SWING buttons
together at the same time, it will activate the
Self-Clean function.
Turbo function
To activate turbo function, press the TURBO
button, and will appear on the display.
Press again to cancel this function.
In COOL/ HEAT mode, when you select the
TURBO feature, the appliance will turn to quick
COOL or quick HEAT mode, and operate the
highest fan speed to blow a strong airflow.
MUTE FUNCTION
1. Press MUTE button to activate this function,
and will appear on the remote display.
Do it again to deactivate this function.
2. When the MUTE function runs, the remote
controller will display the auto fan speed, and
the indoor unit will operate at lowest fan
speed to be quiet feeling.
3. When pressing FAN/ TURBO/ SLEEP button,
the MUTE function will be cancelled. MUTE
function cannot be activated under dry mode
ECO FUNCTION
In this mode the appliance
automatically sets the operation to
save energy.
Press the ECO button, appears on the
display, and the appliance will run in ECO mode.
Press again to cancel it.
Note: The ECO function is available in both
COOLING and HEATING modes.
SLEEP FUNCTION
Pre-setting automatic operating
program.
After 10 hours running in sleep mode, the air
conditioner will change to the previous setting
mode.
Press the SLEEP button to activate the SLEEP
function, and appears on the display.
Press again to cancel this function
DISPLAY FUNCTION (INDOOR DISPLAY)
Switch ON/OFF on the LED
display on panel.
Press the DISPLAY button to switch off the LED
display on the panel. Press again to switch on the
led display
I FEEL FUNCTION
Press the I FEEL button to active the function, the
will appear on the remote display.
Do it again to deactivate this function.
This function enables the remote control to
measure the temperature at its current location,
and send this signal to the air conditioner to
optimize the temperature around you and ensure
your comfort.
It will automatically deactivate 2 hours later.
ANTIMILDEW FUNCTION
Press the button to activate the ANTI-MILDEW
function, will appear on the display. Do it again
to deactivate this function. After running COOL/
DRY for more than 30 minutes, you can operate
this function, the unit will blow airflow for about
15 minutes to dry the inner parts to avoid mildew,
then unit will shut off.
NOTE: AVAILABLE ONLY DRY/ COOLING MODE